Milling

Products

Product lines

Facilitation

• Fuh FXI - Milling angle head (Fixed)

The slope angle of the head spindle is 90°

Pivot head round the axis for 360°

Suitable for finishing operations

Clamping size 2÷16 mm and 2÷20 mm

With fixed taper shank

• Fuh PVI - Milling angle head (Pivoting)

The slope angle of the head spindle is 0-90°

Pivot head round the axis for 360°

Suitable for finishing operations

Clamping size 2÷16 mm and 2÷20 mm

With fixed taper shank

• Fuh FXM - Modular clamping

This model makes possible to change the taper shank, extension part or clamping plate.

It´s construction isn't so rigid as model FXI.

• Fuh PVM - Modular clamping

This model makes possible to change the taper shank, extension part or clamping plate.

It´s construction isn't so rigid as model PVI.

• ZP-10/X - Spindlespeeder

Gear ratio 1:6

Max. spindle speed 20.000 rpm

Power 4,5 kW

Tool diameter 1÷13 mm

• List of the collets type for ranges of clamping:

ER25 Ø 2÷16 mm

ER32 Ø 2÷20 mm

ER20 Ø 1÷13 mm

• Maximal torque by milling angle heads

Fuh PVI ER25 15 Nm

Fuh FXI ER25 18 Nm

Fuh PVI ER32 28 Nm

Fuh FXI ER32 32 Nm

------------------------

Fuh PVM ER25 10 Nm

Fuh FXM ER25 12 Nm

Fuh PVM ER32 18 Nm

Fuh FXM ER32 21 Nm

• Download complete catalogue or parts in PDF

Manuals for Milling angle heads and Spindlespeeders – download in PDF

Fuh - Milling angle head

• Návod Fuh.pdf (3,5MB) - česky

• Instructions Fuh.pdf (3,4MB) - english

• Anleitung Fuh.pdf (2,9MB) - deutsch

• Инструкция Fuh.pdf (3,5MB) -πο-русски

ZP-10/X - Spindlespeeder

• Návod ZP-10/X.pdf (0,4MB) - česky

• Instructions ZP-10/X.pdf (0,4MB) - english

• Anleitung ZP-10/X.pdf (0,4MB) - deutsch

• Инструкция ZP-10/X.pdf (7,2MB) -πο-русски

Facilitation

• Fuh PVI – list of spare parts
• Fuh FXI – list of spare parts

• List of all manuals – download in PDF
• The most often questions (FAQ) Fuh (PDF)
• The most often questions (FAQ) ZP-10/X (PDF)
• Collets ER25 and ER32 DIN 6499-B (Fuh)
• Collets ER20/ESX DIN6499-B (ZP-10/X)

Frequently asked questions (FAQ)

• Is it possible to use milling angel head on any kind of machine tool?

Heads are designed for boring and milling machines with taper shanks SK40 and SK50. If spindle is tipped up in other angel than 0° or 90° than adjustable heads PVI or PVM need NC, CNC machine with continuous control.

• What are conditions for putting the milling angle head on machine tools?

Necessary is to choose suitable machine and beside spindle install retaining block which holds case of head. Block is a part of head accessories. Distance from machine spindle centerline is given by modification of arresting arm. (spot height A)

• What is necessary to consider before purchase of milling angel head?

Usage measure of head, its necessity (head is for filigree not for stocking). Real possibility of head setting on the machine.

• Is it possible to use inner coolant by these heads?

No it is impossible. Heads are not designed for this type of coolant. If you would need it, firm NAREX MTE is able to offer you special solution which will make inner coolant possible.

• What to avoid during using this head?

First of all you must avoid its overloading what has main influence over shortening bearings and bevel gears durability. We recommend the cooling fluid (especially by adjustable heads) not to spray in bigger size on head case. The fluid can get inside the case and destroy bearings.

• What are the most frequent failures of milling angel heads?

Worn bearings on the spindle what will be manifested by marked higher run-out and higher vibration.

• What to consider before purchase of this machine?

Usability and possibility of function test by form of loan.

• What are demands on machine tool?

A - clamping spindle cavity must be in such condition that the clamping is accurate and rigid.
B - spindle and machine table seating must has necessary rigidity to prevention undesirable vibration during machining.

• With what accuracy is possible to clamp tools to the spindlespeeder?

Measured untrue running clamped in diameter "d" in distance 2,5 d from the collet edge:
In diameters range d 1,0 - 10,0 mm is maximum 0,02 mm
In diameters range d 10,0 - 20,0 mm is maximum 0,025 mm.

• How is service life limited?

Machine has lasting grease packing with service life 2.500 running hours. During run in groove should not be the temperature higher than 60°C and noisiness 80 dBA/1m. Spindle run-out should not be higher than 0,025 mm for collet on the cavity edge and axial clearance must be zero everytime.

Product repairing

NAREX MTE standardly provides repairs of produced and delivered products. There are guarantee repairs or normal non guarantee repairs. During repair is product dismounted, there are found defective parts and up to it is determined range and price of repair. After customer´s repair price confirmation are defected parts exchanged, product is again mounted and tested.

Repair speeding

For repair speeding and lower price is suitable to enclose to repair order letter with information about problems (during which conditions defects occurs or indicate required range of repair).

Repair ordering

For repair ordering you should send product for repair, order of repair and specifications of defects on our address:

NAREX MTE Ltd.

sales department

Moskevska 659/63

CZ-101 00 Prague 10
Czech Republic

Information about repair

About repair you will be informed by e-mail or by phone, with any questions you can contact export department on phone: +420 246 002 249, e-mail: sales@narexmte.cz, fax: + 420 246 002 335

NAREX MTE s.r.o.

Moskevska 659/63

CZ-101 00 Prague 10
Czech Republic

Tel:

Fax:

+420-246 002 321

+420-246 002 249

+420-246 002 335

+420-246 002 343

e-mail: sales@narexmte.cz

http://www.narexmte.cz

Support

Basic technical information you can find also on reference service.

NAREX MTE s.r.o.

Moskevska 659/63

CZ-101 00 Prague 10
Czech Republic

Tel:

Fax:

+420-246 002 321

+420-246 002 249

+420-246 002 335

+420-246 002 343

e-mail: sales@narexmte.cz

http://www.narexmte.cz